Get In Touch

No products in the cart.

Get In Touch

No products in the cart.

Get In Touch

Power Electronics Trainer (Model : XPO-PE) / XPO-1 Ph. PE)

Introducing XPO-PE, the microcontroller-based Power Electronics Trainer. This system features an aesthetically designed electronic desk with a master unit providing essential experiment resources, including line-synchronized firing circuits, power supplies, lamp loads, RLC loads, and battery charging supply. The central slot accommodates replaceable experiment panels, secured in sturdy ABS moulded plastic enclosures with colourful, screwless overlays depicting circuits. Connectivity is simplified through robust 4mm banana sockets and patch cords. Each multi-experiment panel comes with a set of comprehensive User Guides. To enhance the learning experience, consider ordering 6 Master units with sets of 6 panels (PE 1 x 2, PE2, PE3, PE6 x 2 nose), along with the Power Scope. Emphasize PE1 and PE6, the major panels, for an optimal understanding of power electronics concepts.

Category:

SALIENT FEATURES:

  • Aesthetically designed injection moulded electronic desk.
  • Master unit carrying useful experiment resources like line Synchronized firing circuits, Power supplies, lamp load, RLC loads, Battery charging supply etc. while the central slot will hold replaceable experiment panels.
  • Each multi experiment panel is secured in an ABS moulded plastic sturdy enclosure, and has colourful screw less overlay showing circuit & Connection through Sturdy 4mm Banana Sockets & Patch Chords.
  • Set of User Guide provided with each unit.
  • Order 6 Master units and set of 6 panels (PE 1 x 2 ,PE2, PE3, PE6X2nos)+ Power scope, buy more of PE1 and PE6 being major panels.

Master Unit

Built in power supply

  • DC supply : + 12V, 500mA,
  • Unregulated Power supply 17V / 750mA,
  • Regulated 7VDC to 14VDC/3A O/P is provided as 12V Battery charging supply. In absence of battery, same may be used as simulated battery source to run experiments on inverters etc.
  • Isolated DC supply +12V/ 300amAwith isolated common.
  • On board Inverter transformer of Primary & Secondaries: 12-11-0-11-12/3A.
  • On board o/p to Isolated Drive Circuit AC supply
  • 230V AC line voltage is made available on two banana 4mm sockets as well as 1.5Afuse extender for variac if used.
  • Aux DC Power Supply :(Useful as field / armature supply for DC motor)
    • Variable upto 200Vdc/0.5Amp (Phase controlled Thyristor half
      bridge)
    • Field ON/OFF control with field failure relay &
      over current protection circuit.

LSPT Panel consisting of:

  • Two pulse transformers of 1:1:1 are provided for isolation & supplying firing pulses along with required DC Power supply to experiment panel under test through 15 pin female ‘D’ connector.
  • Selector switch of 2 pole 6 way for selecting different types of firing pulses like out of phase inverter firing using LM3525 with dead time, freq. Control in freq variation from 170 Hz to 250Hz, 12.5/25/6..25 Hz Frequency gated with High Frequency (3KHz) for Cycloconverter, line Synchronized UJT firing for converter and pulsewidth

R-L-C Load Panel:

  • Load resistor of 10ohm/ 40W and 100ohm / 10W – 1No.each
  • Centre tapped 3Achoke 4mH/ 16mH each -2Nos.
  • DC choke 0-100-200 mH/750mA- 1No.
  • Commutation capacitors of 10uF/100V – 4Nos.
  • AC Paper capacitor of 4uF/440V – 1No.
  • DC Cap 220uF / 63V- 1No.
  • Diode BYT71 (5407)- 1 No.
  • On board Lamp load of 15W/ 230VAC provided

Reviews

There are no reviews yet.

Be the first to review “Power Electronics Trainer (Model : XPO-PE) / XPO-1 Ph. PE)”

Your email address will not be published. Required fields are marked *

Related Products

× How can I help you?